나의 즐겨찾기 | 블로그홈 | 바로가기 바로가기 | 로그인
TEL: 82 - 2 - 873 - 6646 ~ 7
블로그  |  사진갤러리  |  동영상갤러리 방명록  |   즐겨찾기 추가
김광호 (kgh57150)
프로필     
 인기도 :
 이 블로그 점수주기
전체 글보기(2265)
(주)누리인프라
CISCO Networks
NORTEL Networks
Juniper Networks
3COM Networks
Foundry Networks
Extreme Networks
KOREA DASAN Networks
TOTAL SERVERS
무한 이미지 표현?
블로그 공지사항
오늘 전체
방문자 352 541619
구독자 0 2
댓글 0 123
참조글 12 2613
2009 11월
1 2 3 4 5 6 7
8 9 10 11 12 13 14
15 16 17 18 19 20 21
22 23 24 25 26 27 28
29 30
최근 댓글 전체보기
thank you.
thank you.
thank you.
thank you.
정보 감사합니다. 앞..
최근 참조글 전체보기
Buy valium.
Ambein buydr..
Amoxicillin ..
Fioricet.
Buy amoxicil..
다녀간 블로거 더보기
- Choi
- 백만돌
- UCC조아
- lovelovemg
- p12146
1,615
개설일 : 2007/09/03
 

CISCO Router 와 WIC-2T Serial(시리얼), 패스트이더넷(Fastethernet) 완전정복하기

2009.05.12 12:21 | CISCO Networks | 김광호

http://kr.blog.yahoo.com/kgh57150/2214 주소복사


CISCO Router 와 WIC-2T  Serial(시리얼), 패스트이더넷(Fastethernet) 완전정복하기



CISCO Router 와 WIC-2T  Serial(시리얼), 패스트이더넷(Fastethernet) 완전정복
하기


 *** CISCO2611XM Router의 초기화및 FastEthernet Port and WIC-2T Test ***
 

 

01) DCE = 메인 CISCO2611XM 초기화하기

전원을 켠후 컨트롤 + 브레이크키 푸시다운 반복함


C2600 platform with 131072 Kbytes of main memory


monitor: command "boot" aborted due to user interrupt
rommon 1 >
rommon 1 >
rommon 1 >
rommon 1 >
rommon 1 >
rommon 1 >
rommon 1 >
 보충설명: 초기화 명령어
rommon 1 > confreg 0x2142


You must reset or power cycle for new config to take effect
 보충설명: 다시부팅
rommon 2 > reset

System Bootstrap, Version 12.2(8r) [cmong 8r], RELEASE SOFTWARE (fc1)
Copyright (c) 2003 by cisco Systems, Inc.
program load complete, entry point: 0x80008000, size: 0x9049b0
Self decompressing the image : ###################################################################################################################################################### [OK]

Smart Init is enabled
smart init is sizing iomem
  ID            MEMORY_REQ                 TYPE
00036B          0X00103980 C2611XM Dual Fast Ethernet
                0X00098670 public buffer pools
                0X00211000 public particle pools
TOTAL:          0X003ACFF0

If any of the above Memory Requirements are
"UNKNOWN", you may be using an unsupported
configuration or there is a software problem and
system operation may be compromised.
Rounded IOMEM up to: 4Mb.
Using 3 percent iomem. [4Mb/128Mb]

              Restricted Rights Legend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

           cisco Systems, Inc.
           170 West Tasman Drive
           San Jose, California 95134-1706

 

Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-IPBASE-M), Version 12.3(10), RELEASE SOFTWARE (fc3)
Copyright (c) 1986-2004 by cisco Systems, Inc.
Compiled Tue 17-Aug-04 05:10 by kellythw
Image text-base: 0x80008098, data-base: 0x80F20830

cisco 2611XM (MPC860P) processor (revision 0x400) with 126976K/4096K bytes of memory.
Processor board ID  (1133858219)
M860 processor: part number 5, mask 2
Bridging software.
X.25 software, Version 3.0.0.
2 FastEthernet/IEEE 802.3 interface(s)
2 Serial(sync/async) network interface(s)
32K bytes of non-volatile configuration memory.
32768K bytes of processor board System flash (Read/Write)


         --- System Configuration Dialog ---

Would you like to enter the initial configuration dialog? [yes/no]: no


Press RETURN to get started!


*Mar  1 00:00:10.275: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up
*Mar  1 00:00:10.275: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up
*Mar  1 00:00:10.279: %LINK-3-UPDOWN: Interface Serial0/0, changed state to down
*Mar  1 00:00:10.279: %LINK-3-UPDOWN: Interface Serial0/1, changed state to down
*Mar  1 00:00:11.277: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to down
*Mar  1 00:00:11.277: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to down
*Mar  1 00:00:11.281: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed state to down
*Mar  1 00:00:11.281: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/1, changed state to down
*Mar  1 00:00:41.903: %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to administratively down
*Mar  1 00:00:41.903: %LINK-5-CHANGED: Interface Serial0/0, changed state to administratively down
*Mar  1 00:00:41.907: %LINK
Router>-5-CHANGED: Interface FastEthernet0/1, changed state to administratively down
*Mar  1 00:00:41.907: %LINK-5-CHANGED: Interface Serial0/1, changed state to administratively down
*Mar  1 00:00:42.584: %SYS-5-RESTART: System restarted --
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-IPBASE-M), Version 12.3(10), RELEASE SOFTWARE (fc3)
Copyright (c) 1986-2004 by cisco Systems, Inc.
Compiled Tue 17-Aug-04 05:10 by kellythw
*Mar  1 00:00:42.584: %SNMP-5-COLDSTART: SNMP agent on host Router is undergoing a cold start
Router>
Router>en
 보충설명: 설정값 저장하기 위한 명령어
Router#conf t
Enter configuration commands, one   per line.  End with CNTL/Z.
Router(config)#config-register 0x2102
Router(config)#exit
  보충설명: 저장명령어약자: wr
Router#wr
Building configuration...

*Mar  1 00:01:01.211: %SYS-5-CONFIG_I: Configured from console by console[OK]
Router#
Router#
Router#
Router#
Router#

02) DTC = 서브 CISCO2611XM 초기화 하기

System Bootstrap, Version 12.2(8r) [cmong 8r], RELEASE SOFTWARE (fc1)
Copyright (c) 2003 by cisco Systems, Inc.
C2600 platform with 131072 Kbytes of main memory


monitor: command "boot" aborted due to user interrupt
rommon 1 >
rommon 1 >
rommon 1 >
 보충설명: 초기화 명령어
rommon 1 > confreg 0x2142


You must reset or power cycle for new config to take effect
 보충설명: 재부팅하기
rommon 2 > reset

System Bootstrap, Version 12.2(8r) [cmong 8r], RELEASE SOFTWARE (fc1)
Copyright (c) 2003 by cisco Systems, Inc.
C2600 platform with 131072 Kbytes of main memory

program load complete, entry point: 0x80008000, size: 0x9049b0
Self decompressing the image : ###################################################################################################################################################### [OK]

Smart Init is enabled
smart init is sizing iomem
  ID            MEMORY_REQ                 TYPE
00036B          0X00103980 C2611XM Dual Fast Ethernet
                0X00098670 public buffer pools
                0X00211000 public particle pools
TOTAL:          0X003ACFF0

If any of the above Memory Requirements are
"UNKNOWN", you may be using an unsupported
configuration or there is a software problem and
system operation may be compromised.
Rounded IOMEM up to: 4Mb.
Using 3 percent iomem. [4Mb/128Mb]

              Restricted Rights Legend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

           cisco Systems, Inc.
           170 West Tasman Drive
           San Jose, California 95134-1706

 

Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-IPBASE-M), Version 12.3(10), RELEASE SOFTWARE (fc3)
Copyright (c) 1986-2004 by cisco Systems, Inc.
Compiled Tue 17-Aug-04 05:10 by kellythw
Image text-base: 0x80008098, data-base: 0x80F20830

cisco 2611XM (MPC860P) processor (revision 0x401) with 126976K/4096K bytes of memory.
Processor board ID  (718809216)
M860 processor: part number 5, mask 2
Bridging software.
X.25 software, Version 3.0.0.
2 FastEthernet/IEEE 802.3 interface(s)
2 Serial(sync/async) network interface(s)
32K bytes of non-volatile configuration memory.
32768K bytes of processor board System flash (Read/Write)


         --- System Configuration Dialog ---

Would you like to enter the initial configuration dialog? [yes/no]: no


Press RETURN to get started!


*Mar  1 00:00:-5-CHANGED: Interface FastEthernet0/1, changed state to administratively down
*Mar  1 00:00:15.216: %LINK-5-CHANGED: Interface Serial0/1, changed state to administratively down
*Mar  1 00:00:15.893: %SYS-5-RESTART: System restarted --
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-IPBASE-M), Version 12.3(10), RELEASE SOFTWARE (fc3)
Copyright (c) 1986-2004 by cisco Systems, Inc.
Compiled Tue 17-Aug-04 05:10 by kellythw
*Mar  1 00:00:15.893: %SNMP-5-COLDSTART: SNMP agent on host Router is undergoing a cold start
Router>
Router>en
Router#
 보충설명: 터미널의약자 = 명령어 작업을 위한 장소
Router#conf t
Enter configuration commands, one   per line.  End with CNTL/Z.
 보충설명: 설정값 저장하기 위한 명령어
Router(config)#config-register 0x2102
Router(config)#exit
 보충설명: 현재 설정값 저장하기: wr 약자임
Router#wr
Building configuration...

*Mar  1 00:00:33.542: %SYS-5-CONFIG_I: Configured from console by console[OK]
Router#
 보충설명: 현재 장비의 전체 모듈 나타내는 명령어
Router#sh diag
Slot 0:
        C2611XM 2FE Mainboard Port adapter, 4 ports
        Port adapter is analyzed
        Port adapter insertion time unknown
        EEPROM contents at hardware discovery:
        Hardware Revision        : 4.0
        PCB Serial Number        : (1133858219)
        Part Number              : 73-7679-06
        RMA History              : 00
        RMA Number               : 0-0-0-0
        Board Revision           : A0
        Deviation Number         : 0-0
        EEPROM format version 4
        EEPROM contents (hex):
          0x00: 04 FF 40 03 6B 41 04 00 C1 18 46 48 4B 30 39 30
          0x10: 36 46 30 35 38 20 28 31 31 33 33 38 35 38 32 31
          0x20: 39 29 82 49 1D FF 06 04 00 81 00 00 00 00 42 41
          0x30: 30 80 00 00 00 00 FF FF FF FF FF FF FF FF FF FF
          0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

        WIC Slot 0:
        Serial 2T (12in1)
        Hardware revision 1.0           Board revision G0
        Serial number                   Part number    800-03181-01
        Test history      0x0           RMA number     00-00-00
        Connector type    PCI
        EEPROM format version 1
        EEPROM contents (hex):
          0x20: 01 12 01 00 01 BB 16 5E 50 0C 6D 01 00 00 00 00
          0x30: 80 00 00 00 02 09 23 00 FF FF FF FF FF FF FF FF

 보충설명: 현재 설정값을 보기위한 명령어
Router#sh run
Building configuration...

Current configuration : 662 bytes
!
version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Router
!
boot-start-marker
boot-end-marker
!
!
no network-clock-participate slot 1
no network-clock-participate wic 0
no aaa new-model
ip subnet-zero
ip cef
!
!
!
no ftp-server write-enable
!        
!
!
!
interface FastEthernet0/0
 no ip address
 shutdown
 duplex auto
 speed auto
!
interface Serial0/0
 no ip address
 shutdown
!
interface FastEthernet0/1
 no ip address
 shutdown
 duplex auto
 speed auto
!
interface Serial0/1
 no ip address
 shutdown
!        
ip classless
no ip http server
!
!
line con 0
line aux 0
line vty 0 4
!
!
end
 
 보충설명: 현재 플레시메모리의 총용량및 IOS = 운영체계 나타내는 명령어
Router#sh flash:

System flash directory:
File  Length   Name/status
  1   9456332  c2600-ipbase-mz.123-10.bin 
[9456396 bytes used, 23573744 available, 33030140 total]
32768K bytes of processor board System flash (Read/Write)

Router#
Router#conf t
Enter configuration commands, one   per line.  End with CNTL/Z.
 보충설명: 시리얼(WIC-2T) 가상 IP 넣기
Router(config)#int s0/0   ---- 보충설명: Serial 0슬롯의 0라는뜻
                               포트가 많아지면 1,2,3,4....로 나타남
                               int 인터페이스의 약자임

Router(config-if)#ip add 10.10.2.1 255.255.255.0 --- 보충설명: add 어드레스의 약자임
 보충설명: sh 숏타운의 약자임
Router(config-if)#no sh
Router(config-if)#
*Mar  1 00:06:10.029: %LINK-3-UPDOWN: Interface Serial0/0, changed state to down
 보충설명: 시리얼 구간 테스트의 메인 DCE 알려주려는 명령어
Router(config-if)#clock rate 2000000
Router(config-if)#exit
Router(config)#exit
 보충설명: 설정값 확인하기
Router#sh run
*Mar  1 00:06:47.054: %SYS-5-CONFIG_I: Configured from console by console
Building configuration...

Current configuration : 692 bytes
!
version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Router
!
boot-start-marker
boot-end-marker
!
!
no network-clock-participate slot 1
no network-clock-participate wic 0
no aaa new-model
ip subnet-zero
ip cef
!
!
!
no ftp-server write-enable
!        
!
!
!
interface FastEthernet0/0
 no ip address
 shutdown
 duplex auto
 speed auto
!
interface Serial0/0
 ip address 10.10.2.1 255.255.255.0
 clockrate 2000000
!
interface FastEthernet0/1
 no ip address
 shutdown
 duplex auto
 speed auto
!
interface Serial0/1
 no ip address
 shutdown
!        
ip classless
no ip http server
!
!
line con 0
line aux 0
line vty 0 4
!
!
end

 03) DTE 서브 CISCO2611XM 가상 IP 넣기

 보충설명: 기본 명령어는 DCE 메인과 같음
Router#
Router#conf t
Enter configuration commands, one   per line.  End with CNTL/Z.
Router(config)#int s0/0
Router(config-if)#ip add 10.10.2.3 255.255.255.0
Router(config-if)#no sh
Router(config-if)#exit
Router(config)#
*Mar  1 00:05:29.198: %LINK-3-UPDOWN: Interface Serial0/0, changed state to up
*Mar  1 00:05:30.200: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed state to u
Router(config)#exit
 보충설명: 설정값 확인하기
Router#sh run
*Mar  1 00:05:34.411: %SYS-5-CONFIG_I: Configured from console by console
Building configuration...

Current configuration : 673 bytes
!
version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Router
!
boot-start-marker
boot-end-marker
!
!
no network-clock-participate slot 1
no network-clock-participate wic 0
no aaa new-model
ip subnet-zero
ip cef
!
!
!
no ftp-server write-enable
!        
!
!
!
interface FastEthernet0/0
 no ip address
 shutdown
 duplex auto
 speed auto
!
interface Serial0/0
 ip address 10.10.2.3 255.255.255.0
!
interface FastEthernet0/1
 no ip address
 shutdown
 duplex auto
 speed auto
!
interface Serial0/1
 no ip address
 shutdown
!
ip classless
no ip http server
!
!
line con 0
line aux 0
line vty 0 4
!
!
end
 
04) DCE 메인 가상 IP 테스트 하기

Router#

Router#ping 10.10.2.1

 보충설명: WIC-2T용 스마트케이블의 DCE, DTE 를 장비와 똑같이 맞추어야함

 설정이 올바르면 WIC-2T의 LED 램프에 불이 들어와야함
 
 점등이 않되면 케이블이나 WIC-2T의 불량일 가능성이 높음
 
 보충설명: 단기적 테스트
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.10.2.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms
Router#ping 10.10.2.1

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.10.2.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms
Router#ping 10.10.2.1

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.10.2.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms
 
 보충설명: 장기적 테스트

Router#p
Protocol [ip]:
Target IP address: 10.10.2.1
Repeat count [5]: 1000
Datagram size [100]: 1000
Timeout in seconds [2]:
Extended commands [n]:
Sweep range of sizes [n]:
Type escape sequence to abort.
Sending 1000, 1000-byte ICMP Echos to 10.10.2.1, timeout is 2 seconds:
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!
Success rate is 100 percent (1000/1000), round-trip min/avg/max = 8/10/32 ms

05) CISCO2611XM 의 Fastethernet port 테스트하기


Router#
Router#
Router#conf t
Enter configuration commands, one   per line.  End with CNTL/Z.

 보충설명: Fastethernet 약자 f
   
Router(config)#int f0/0 -----  보충설명: Fastethernet 0슬롯의 0라는뜻
                               포트가 많아지면 1,2,3,4....로 나타남
                               페스트이더넷 은 10/100M를 지원한다는뜻임
                               Ethernet "e0/0" 로 표기됨 10M 전용
                               케이블은 RJ45 크로스케이블로 연결해야함
                               int 인터페이스의 약자임
Router(config-if)#ip add 192.168.10.200 255.255.255.0
Router(config-if)#no sh
Router(config-if)#exit
Router(config)#exit
Router#
*Mar  1 00:11:04.408: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up
*Mar  1 00:11:05.814: %SYS-5-CONFIG_I: Configured from console by console

 보충설명: 설정값 보기

Router#sh run
Building configuration...

Current configuration : 708 bytes
!
version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Router
!
boot-start-marker
boot-end-marker
!
!
no network-clock-participate slot 1
no network-clock-participate wic 0
no aaa new-model
ip subnet-zero
ip cef
!
!
!
no ftp-server write-enable
!        
!
!
!
interface FastEthernet0/0
 ip address 192.168.10.200 255.255.255.0
 duplex auto
 speed auto
!
interface Serial0/0
 ip address 10.10.2.1 255.255.255.0
 clockrate 2000000
!
interface FastEthernet0/1
 no ip address
 shutdown
 duplex auto
 speed auto
!
interface Serial0/1
 no ip address
 shutdown
!
ip classless
no ip http server
!
!
line con 0
line aux 0
line vty 0 4
!
!
end
 
 다른장비 CISCO2611XM 가상 IP 넣기

Router#conf t
Enter configuration commands, one   per line.  End with CNTL/Z.
Router(config)#int f0/0
Router(config-if)#ip add 192.168.10.230 255.255.255.0
Router(config-if)#no sh
Router(config-if)#exit
Router(config)#exit
*Mar  1 00:08:32.355: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up
Router#
Router#
*Mar  1 00:08:33.961: %SYS-5-CONFIG_I: Configured from console by consoleping 192.168.10
*Mar  1 00:08:38.224: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up.200

 단기적 테스트 하기

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.10.200, timeout is 2 seconds:
.!!!!
Success rate is 80 percent (4/5), round-trip min/avg/max = 1/2/4 ms
Router#ping 192.168.10.200

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.10.200, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms
Router#ping 192.168.10.200

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.10.200, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms

장기적 테스트하기

Router#p           
Protocol [ip]:
Target IP address: 192.168.10.200
Repeat count [5]:
Datagram size [100]:
Timeout in seconds [2]:
Extended commands [n]:
Sweep range of sizes [n]:
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.10.200, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms
Router#p
Protocol [ip]:
Target IP address: 192.168.10.200
Repeat count [5]: 1000
Datagram size [100]: 10000
Timeout in seconds [2]:
Extended commands [n]:
Sweep range of sizes [n]:
Type escape sequence to abort.
Sending 1000, 10000-byte ICMP Echos to 192.168.10.200, timeout is 2 seconds:
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!
Success rate is 100 percent (1000/1000), round-trip min/avg/max = 20/21/48 ms
Router#
Router#sh run
Building configuration...

Current configuration : 689 bytes
!
version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Router
!
boot-start-marker
boot-end-marker
!
!
no network-clock-participate slot 1
no network-clock-participate wic 0
no aaa new-model
ip subnet-zero
ip cef
!
!
!
no ftp-server write-enable
!        
!
!
!
interface FastEthernet0/0
 ip address 192.168.10.230 255.255.255.0
 duplex auto
 speed auto
!
interface Serial0/0
 ip address 10.10.2.3 255.255.255.0
!
interface FastEthernet0/1
 no ip address
 shutdown
 duplex auto
 speed auto
!
interface Serial0/1
 no ip address
 shutdown
!
ip classless
no ip http server
!
!
line con 0
line aux 0
line vty 0 4
!
!
end
 
장비의 가상 IP 지우기


 시리얼구간 지우기
Router#
Router#conf t
Enter configuration commands, one   per line.  End with CNTL/Z.
Router(config)#int s0/0
Router(config-if)#no ip add
Router(config-if)#no sh
Router(config-if)#exit
Router(config)#exit

 페스트이더넷 구간 지우기

Router#c
*Mar  1 00:10:23.344: %SYS-5-CONFIG_I: Configured from console by consoleonf t
Enter configuration commands, one   per line.  End with CNTL/Z.
Router(config)#int f0/0
Router(config-if)#no ip add
Router(config-if)#no sh
Router(config-if)#exit
Router(config)#exit
Router#

 설정값 보기

*Mar  1 00:10:43.558: %SYS-5-CONFIG_I: Configured from console by console
Router#sh run
Building configuration...

Current configuration : 642 bytes
!
version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Router
!
boot-start-marker
boot-end-marker
!
!
no network-clock-participate slot 1
no network-clock-participate wic 0
no aaa new-model
ip subnet-zero
ip cef
!
!
!
no ftp-server write-enable
!        
!
!
!
interface FastEthernet0/0
 no ip address
 duplex auto
 speed auto
!
interface Serial0/0
 no ip address
!
interface FastEthernet0/1
 no ip address
 shutdown
 duplex auto
 speed auto
!
interface Serial0/1
 no ip address
 shutdown
!
ip classless
no ip http server
!
!
line con 0
line aux 0
line vty 0 4
!
!
end

Router#
*Mar  1 00:10:55.601: %LINK-3-UPDOWN: Interface Serial0/0, changed state to down
*Mar  1 00:10:56.603: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed state to down
*Mar  1 00:10:58.230: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to down
Router#sh run
Building configuration...

Current configuration : 642 bytes
!
version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Router
!
boot-start-marker
boot-end-marker
!
!
no network-clock-participate slot 1
no network-clock-participate wic 0
no aaa new-model
ip subnet-zero
ip cef
!
!
!
no ftp-server write-enable
!        
!
!
!
interface FastEthernet0/0
 no ip address
 duplex auto
 speed auto
!
interface Serial0/0
 no ip address
!
interface FastEthernet0/1
 no ip address
 shutdown
 duplex auto
 speed auto
!
interface Serial0/1
 no ip address
 shutdown
!
ip classless
no ip http server
!
!
line con 0
line aux 0
line vty 0 4
!
!
end
 
다른 장비 IP 지우기

아래 명령어에서 보듯이 "no" 를 붙이면 사용 않한다는뜻임.


Router#           
Router#conf t
Enter configuration commands, one   per line.  End with CNTL/Z.
Router(config)#int s0/0
Router(config-if)#no ip add
Router(config-if)#no clock rate 2000000
Router(config-if)#no sh
Router(config-if)#exit
Router(config)#exit
Router#conf t
Enter configuration commands, one   per line.  End with CNTL/Z.
Router(config)#
*Mar  1 00:15:17.647: %SYS-5-CONFIG_I: Configured from console by console   
Router(config)#int f0/0
Router(config-if)#no ip add
Router(config-if)#no sh
Router(config-if)#exit
Router(config)#exit
Router#sh ru
*Mar  1 00:15:42.083: %SYS-5-CONFIG_I: Configured from console by consolen
Building configuration...

Current configuration : 642 bytes
!
version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Router
!
boot-start-marker
boot-end-marker
!
!
no network-clock-participate slot 1
no network-clock-participate wic 0
no aaa new-model
ip subnet-zero
ip cef
!
!
!
no ftp-server write-enable
!        
!
!
!
interface FastEthernet0/0
 no ip address
 duplex auto
 speed auto
!
interface Serial0/0
 no ip address
!
interface FastEthernet0/1
 no ip address
 shutdown
 duplex auto
 speed auto
!
interface Serial0/1
 no ip address
 shutdown
!
ip classless
no ip http server
!
!
line con 0
line aux 0
line vty 0 4
!
!
end

Router#


위와 같이 응용하면 어떤 라우터(Router) 나 스위치(Switch)를 통해서도

같은 패턴으로 나가기 때문에 많은 도움이 되었으면 합니다.

감사합니다.


 
** Home Page **

(주) 누리인프라   법인설립됨

www.hardwarebank.net  브랜드명

www.hwbank.co.kr    브랜드병


sales@hardwarebank.net  브랜드명


** site **

http://kr.blog.yahoo.com/kgh57150

http://blog.paran.com/hardwarebank
http://club.paran.com/club/home.do?clubid=hardwarebank

http://blog.danawa.com/hardwarebank

http://blog.daum.net/hardwarebank/?_top_blogtop=go2myblog
http://cafe.daum.net/hardwarebank

http://blog.naver.com/kkh57150
http://cafe.naver.com/hardwarebank.cafe

yahoo gugi
http://kr.gugi.yahoo.com/detail/detailInfo/DetailInfoAction.php?cid=2625981316&p=%C7%CF%B5%E5%BF%FE%BE%EE%B9%F0%C5%A9

http://eroom.korea.com/hardwarebank  : 블로그 종료

http://eroom.korea.com/Eroommain/TalktalkSub.aspx?bid=bbs_94468&cate=1553246

http://blog.empas.com/kgh57150/ : 블로그 종료


http://www.reviewist.co.kr/review/list.php?rg_id=1&rc_id=1

저작자 표시비영리 사용비영리 사용변경금지변경금지
  추천(0) 스크랩 (0) 인쇄

댓글쓰기

댓글쓰기 입력폼

포스트 목록 닫기

목록보기